What model of tractor, and what model/size of blower would go with it? With that information, it's not too hard to go to JD Parts online and look up the exact name and its JD part number....

 

There was a member here that had an online source for the spring loaded pins.

I cant remember though..
They are 5/8" tho

 

www.McMaster.com :fing32:

I can look 'em up later if needed.

 

It's the weld on bracket with the spring loaded pin that is used to attach the snowblower on the 316-318... I want the whole assembly, bracket and spring loaded pin, will weld on my plow attachment for quicker removal....thanks

 

It is realy difficult to know which parts you need.

Try this link into the John Deere Parts Catalog.
http://jdpc.deere.com/jdpc/servlet/com.deere.u90490.partscatalog.view.servlets.HomePageServlet_Alt

I Believe that you are seeking Parts # 15,#16, and #17.

Good luck in your search.

Jerry

 

This is a bracket welded to the snowblower mounting plate, pull the spring loaded pin, turn it to keep it in place when attaching the blower, then turn the spring loaded pin and it pops into the tractor front mounting hole, any one with a 316 or 318 and a blower knows what this is....went on jd parts online and cannot bring up a single diagram...

 

This is the bracket I'm assuming you are talking about, for a Quick-Tach 318 blower... Bracket is #18, is the pin you're talking about #s 11,13, and 14?...

1 03H1505 BOLT 1 5/16" X 1-3/4"
2 A15147 SPRING LOCKING PIN 2
3 H110730 FLANGE NUT 1 (SUB FOR M121011)
4 AM37983 HYDR.QUICK COUPLER PLUG 2
5 M70728 CAP 2
6 AM119926 HOSE 2
7 M121010 BRACKET 1 (NLA)
8 19H3415 CAP SCREW 1 (SUB FOR AM119923)
9 AM119924 PIVOT 1 (NLA)
10 K40016 LOCK NUT 1
Cart KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
11 M42578 COMPRESSION SPRING 4
12 AH63565 ELBOW FITTING 2 (INCLUDES O-RING R28782)
13 M97609 PIN FASTENER 4
14 34H385 SPRING PIN 4 1/4" X 1-3/4"
15 AM119973 HYDRAULIC CYLINDER 1
16 ........ FRAME 1 (318/322/332) (ORDER BM18121)
........ FRAME 1 (420/430) (ORDER BM18122)
17 M91212 PIN FASTENER 2
18 ........ FRAME 1 TRACTOR MOUNT, (ORDER BM18121 (318/322/332) OR BM18122 (420/430))
19 A29647 SPACER 1
Cart KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
20 M121012 PIN 1 (318/322/332)
M121013 PIN 1 (420/430)
21 M40514 SNAP RING 2
22 BM18121 KIT 1 FRONT HITCH (318/322/332)
BM18122 KIT 1 FRONT HITCH (420/430)
23 M114803 PIN 1
24 A3581R SPRING LOCKING PIN 1
25 M84180 RING 1
26 AH97869 LINK CHAIN 1
27 M88183 RING 1

 

Not exactly like the Deere ones, but should work I would think.
http://www.agrisupply.com/Spring-Pin-Latch-Plain-Tube-Long-Pin/p/54723/&sid=&eid=/
:thThumbsU

 

I think he wants the ones like on a #49 blower

 

Oh okay, so THIS one....

1 M42485 BELT 1 (120, 140, 300, 312, 314 AND 316)
M82719 BELT 1 (317) (318, 316, S.N. 285001- )
M91270 BELT 1 (330, 322 AND 332)
2 AM103464 SHEAVE 1 (SUB FOR AM31237)
3 22H843 SET SCREW 2 3/8" X 7/16"
4 ........ SHAFT KEY 1 (CUT FROM H64373)
5 19H1800 CAP SCREW 1 3/8" X 1-1/2"
12H304 LOCK WASHER 1 3/8"
14H1076 NUT 1 3/8"
6 AM103018 IDLER 1 (SUB FOR M41647)
Cart KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
7 24H1162 WASHER AR 17/32" X 1-1/4" X 0.060"
8 S138M EXTENSION SPRING 1
9 19H1765 CAP SCREW 1 3/8" X 1-3/4"
14H1076 NUT 1 3/8"
12H304 LOCK WASHER 1 3/8"
10 24H1176 WASHER 2 13/32" X 1-1/4" X 0.100"
11 AM31322 BRACKET 1
12 M42490 WASHER 1
13 M42578 COMPRESSION SPRING 2
14 M42579 PIN 2
Cart KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
15 34H385 SPRING PIN 2 1/4" X 1-3/4"
16 AM31259 SUPPORT 1 - 9275 (3 GEAR BOX MOUNTING HOLES) (SUB AM34010)
AM34010 BRACKET 1 9276 - (4 GEAR BOX MOUNTING HOLES)
17 24H1789 WASHER 1 17/32" X 1-1/4" X 0.105"
18 M49173 BUSHING 1 (SUB FOR M42477, THIS APPLICATION)
19 19H1777 CAP SCREW 1 1/2" X 1-3/4"
E50302 LOCK NUT 1 (SUB FOR M63368)
20 M42479 BUSHING 1
21 AM31233 ARM 1
22 24H1308 WASHER 1 13/32" X 1" X 0.134"
Cart KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
23 19H2054 CAP SCREW 1 3/8" X 4-3/4"
12H304 LOCK WASHER 1 3/8"
14H1076 NUT 1 3/8"

 

It was just a guess LTG :dunno: What say he ???

 

Parts 13, 14, and 15 are part of it, also wanted the small bracket that is welded to the sideplate that the pins go through, that way, I can drill a hole in my homemade mounting, weld the bracket and pin assembly and this would be similar to the top mounting pins on the pictured snowblower,...I was hoping for an aftermarket source to buy the pin/bracket asembly....JD does not show a number for the weld on part.....thanks

 

That's likely because its included in 16, the frame... Sounds like your best bet then may be those ones that RealBiker posted the link to, from AgriSupply.... You could either weld them on as is, or cut the bottom of the enclosing piece off and weld them a bit shorter....

 

So, Little tractor guy, how did you get the diagram with parts numbers....

 

The weld on part is part of the assembly from deere... Gonna have to fab that part

 

Pretty positive you can't get the bracket that welds on. I have made them pretty easy using unistrut

 

I went to the JD parts site at http://jdpc.deere.com/jdpc/servlet/com.deere.u90490.partscatalog.view.servlets.HomePageServlet_Alt

Chose Model Search

Put 49 into the Model blank and checked "Exact Search", clicked Find, that brought up the listing for the 1080 - 49-Inch Tractor-Mounted Snow Throwers - 30Aug01

Expanded that one out using the "+" to the left of it

Chose Sectional Index, selected 12 - Tractor Mount and Idler, that brought up the diagram. Right-clicked over the diagram and chose Copy Image Address (that might be a slightly different selection depending on what browser you are using),

then went to a new post on MTF, inserted an image using the Insert Image tool (looks like a little picture of a mountain) and pasted the address for that diagram into the Insert Image blank....

Then I went back to the Sectional index and copied the whole list of part numbers, pasted it into the post under the diagram....

 

Get a crapped out #49 blower ( certainly should be some) and cut them off and you will have ALL the parts.

 

http://www.etrailer.com/Enclosed-Trailer-Parts/Redline/SL58W.html

 

Here are the ones I made.

 

A.W direct has some latch pins, one has a short throw with 5/8 pins and they have one with 5/8 pins that has a longer throw, similar to the one realbiker shows.

 

I have used the ones Pete is referring to.I used them here on my front weight bracket.
However I like Butchfords design much better.That is the closest I have seen to the original style yet.

AJ

 

:thThumbsU

Great thread. Just one more thing that I didn't realize you could buy off the shelf. I'd like to put some of these on a trailer I have to secure the end gate - and so people who borrow it quit losing the pins that are now used!