Hi, Have a pk 1618 I need a new belt for it I can buy one but does the pully from the pump have to be straight over the pully that is down from it.
Hydraulic pump belt
dutchmanct
21 - 39 of 39 Posts
Joined
·
102 Posts
Ok that is good to hear:thanku:
Joined
·
102 Posts
can somebody tell what kind of hydro pump is on my PK
Joined
·
654 Posts
Webster 15 YB for a non loader 58 YB with a loader.
Joined
·
102 Posts
Is there away to check what I have...
Joined
·
102 Posts
Than I have the 58
Joined
·
102 Posts
well I started to change the belt and order a new tension kit from the guy in Texas. So I hope after it is all done it would be better. Thinking of replacing the pump too anybody can tell me what pump will work.
Joined
·
15,218 Posts
You can buy much better link-belt.
This is what i use. As long as you dont have a back idler pulley it works great.
http://www.ebay.com/itm/Dayco-Adjus...ink-V-belt-material-NOS-/230716275844?pt=LH_DefaultDomain_0&hash=item35b7c2fc84
This is what i use. As long as you dont have a back idler pulley it works great.
http://www.ebay.com/itm/Dayco-Adjus...ink-V-belt-material-NOS-/230716275844?pt=LH_DefaultDomain_0&hash=item35b7c2fc84
Joined
·
15,218 Posts
Joined
·
102 Posts
I bought 2 belts from napa...Thanks for the info
Joined
·
654 Posts
Did you buy the green belt? If not, take them back and ask for the same belt with a "W" on the end. You'll be glad you did!:fing32:
Joined
·
102 Posts
I bought the green ones
Joined
·
2,551 Posts
Is your pump not working? If it's working, why replace it?
Joined
·
102 Posts
Well yesterday I had the loader with some wood and it din't raise so I am hoping that the new belt will help but always ready for the worst.
And if I have the 15yb and not the 58yb pump
Joined
·
2,551 Posts
It didn't raise because you have the link belt on there and it's not tight enough. I went through the link belt thing with mine and I will never put another on a loader tractor. Get them tight, they stretch and eventually break. Mine lasted 6 months. The green belts will help. That's what I'm running now. Make sure the pulley on the pump is tight too. Been there, done that. Once you get the belts on tight and know that everything else is tight, then give it a try. Bet you will see a big difference. Remember, when it's cold out, your hydraulics are going to move slow until they get warmed up. I doubt you have a 15yb pump. The new belts will tell the story. Once on and tight, your three point should raise very quickly. I always tell people that I think I could throw the counterweight up and over my head it raises so fast. Before you go thinking pump, try the small stuff.
Joined
·
102 Posts
Thanks....will try to do that first and than will take from there one step at the time
Joined
·
654 Posts
My old belt was slipping badly. It's the one I replaced in my belt chamging procedure thread. Between the belt slipping and cold oil, I had a heck of a time using the loader last winter but it did work some. Change the belt. It's not that hard a job and you can always change the pump later if you have too. The pics of your pump look like the bigger one to me.
Joined
·
102 Posts
I am all set only have to wait for the tension kit to come in and I will find out if evrything is working. The pump is 4" long and Jas11964 said that was the good one for the loader
21 - 39 of 39 Posts
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
