37-A snowblower help

Deere 214

· Registered

Joined Mar 29, 2012

·

338 Posts

Discussion starter · #1 · Jan 1, 2014

Only show this user

Hi all I been trying to figure out how to hook up my 37-A snowblower to my 110 sf. Anyone have a picture of how the belt goes on to the tractor? An where the shoot arm goes on the tractor? Thanks any help is greatly appreciated.

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#2 · Jan 1, 2014

Only show this user

First is belt routing, 2nd is lift linkage from rocker to front (this is shown on a 2xx series but they are very similar) and last is the short arm from the blower to the linkage, I don't have any for the chute control but it does require a brace that mounts below the variator.

 

Attachments

• 
  FrontLiftinstall[1].jpg
  31.9 KB Views: 1,456
• 
  Shortarm[1].jpg
  42.9 KB Views: 788

Deere 214

· Registered

Joined Mar 29, 2012

·

338 Posts

Discussion starter · #3 · Jan 1, 2014

Only show this user

Thanks that helps. An does the belt go to pulley on the side of motor? Or does it require a special adapter?

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#4 · Jan 1, 2014

Only show this user

Pulley on the side is where it goes. Should go around the outside pulley:

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#5 · Jan 1, 2014

Only show this user

By the way here is the diagram with the chute holder:

 

deerenut

· new nut but loving it

Joined Nov 25, 2010

·

1,594 Posts

#6 · Jan 2, 2014

Only show this user

I am thinking that you are missing the pulley. #22 in PA's diagram... or not. These are pictures of a 212 that I had taken pictures before....

Or here is the routing on a 1970 square fender 110... Not a snowblower, but it is the same pulley that the belt will run on.

 

Deere 214

· Registered

Joined Mar 29, 2012

·

338 Posts

Discussion starter · #7 · Jan 2, 2014

Only show this user

On the PTO pulley but when I tried putting it on it rubs on front upright. Its the same pulley I use for the mower deck.

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#8 · Jan 2, 2014

Only show this user

I would guess that your engine mounts are worn and allowing some twist of the engine. This is a common issue on the SF 110, 112 and 2xx series when the mounts wear out.

 

deerenut

· new nut but loving it

Joined Nov 25, 2010

·

1,594 Posts

#9 · Jan 2, 2014

Only show this user

That is the wrong pulley... if it is the one you use for your mower.

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#10 · Jan 2, 2014

Only show this user

Can you take a picture and post, that would help us a lot in evaluating the problem.

 

Deere 214

· Registered

Joined Mar 29, 2012

·

338 Posts

Discussion starter · #11 · Jan 2, 2014

Only show this user

What's it suppose to look like?

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#12 · Jan 2, 2014

Only show this user

deerenut said:

I am thinking that you are missing the pulley. #22 in PA's diagram... or not. These are pictures of a 212 that I had taken pictures before....



Or here is the routing on a 1970 square fender 110... Not a snowblower, but it is the same pulley that the belt will run on.

Click to expand...

Like the one on this picture.

 

Deere 214

· Registered

Joined Mar 29, 2012

·

338 Posts

Discussion starter · #13 · Jan 2, 2014

Only show this user

Is that Tecumseh motor? Mine has the Kohler motor same as my 112,210,214 and my parts 110

 

AAIndigo

· Registered

Joined Sep 7, 2013

·

41 Posts

#14 · Jan 2, 2014

Only show this user

Deere 214 said:

Is that Tecumseh motor? Mine has the Kohler motor same as my 112,210,214 and my parts 110

Click to expand...

I have a Kohler motor and the set up is the same as Deerenut shows

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#15 · Jan 2, 2014

Only show this user

The JD parts site shows that the 110 had a Kohler, the 112 had either the Techcumseh or the Kohler. The PTO clutch and extra sheave is the same on the 110 and 112 no matter the engine.

 

deerenut

· new nut but loving it

Joined Nov 25, 2010

·

1,594 Posts

#16 · Jan 2, 2014

Only show this user

Loading a video to Youtube.... should help. Man it is cold in the shed! :tee:

Stand by......

 

deerenut

· new nut but loving it

Joined Nov 25, 2010

·

1,594 Posts

#17 · Jan 2, 2014

Only show this user

Having some technical difficulties here tonight.... message is saying can not connect with youtube server... I will try a picture.

stay tuned....

 

Deere 214

· Registered

Joined Mar 29, 2012

·

338 Posts

Discussion starter · #18 · Jan 2, 2014

Only show this user

I went an looked at my parts 110 an saw there is a third pulley bolted to the clutch pulley so I think I need to put that on the other 110 to make it work. If I could figure out how upload a picture of it then I could show you guys lol

 

PA318Guy

· Super Moderator

Joined Sep 4, 2009

·

54,635 Posts

#19 · Jan 2, 2014

Only show this user

Chose "Go Advanced" instead of "Post Quick Reply" then "Manage Attachments" in the next screen.

 

Wfburton159

· Registered

Joined Jan 29, 2010

·

1,657 Posts

#20 · Jan 2, 2014

Only show this user

You need the pulley that bolts the the outside of the pto. It is almost a six inch diameter pulley. This way the belt will be on the outside of the upright. Pulley will look like the one posted early in the thread. Look on page one.