[Jaredfly]

I found a 45 loader for sale about 5 hours from me. Really wanting to buy it but i have a few questions that the fella selling it cant answer. This loader is removed from a X585. Comes with the Relief valve part number BM15044 and the valve for the X485 that i have calls for BM15043 Is there a difference in the 2 ? I have googled the part numbers and the cost for each valve is the same money. All i can think of is since the X5's are 4x4 maybe a different pressure setting within ? Not sure but i know if i dont have to spend the 150.00 on the valve i wont, But.... I dont want to mess anything up with my hydro running and X5 valve.

Has anyone ever installed the valve themselves ? What all is involved in doing that and the rear cut off valve ?

Thanks for the help.

 

[JD X728]

I found a 45 loader for sale about 5 hours from me. Really wanting to buy it but i have a few questions that the fella selling it cant answer. This loader is removed from a X585. Comes with the Relief valve part number BM15044 and the valve for the X485 that i have calls for BM15043 Is there a difference in the 2 ? I have googled the part numbers and the cost for each valve is the same money. All i can think of is since the X5's are 4x4 maybe a different pressure setting within ? Not sure but i know if i dont have to spend the 150.00 on the valve i wont, But.... I dont want to mess anything up with my hydro running and X5 valve.

Has anyone ever installed the valve themselves ? What all is involved in doing that and the rear cut off valve ?

Thanks for the help.

Congratulations! Don't worry so much.

You have to be able to losen one fitting and substitute the valve. Then connect the hose to the outlet from the valve.

Jerry

 

[10ford]

From the Deere45 loader manual...


IMPORTANT: Avoid damage! Clean transaxle before removing valve. Contamination of hydraulic system may cause damage.


MX13498

16. Remove existing free-wheeling valve (J) from right-hand location.

IMPORTANT: Avoid damage! Use correct transaxle hydrostatic pressure relief valve.

• Two-Wheel Drive Machines: Use BM15043 (AM121248) which has “2WD” stamped on valve.

• Four-Wheel Drive Machines: Use BM15044 (AM122228) which has “4WD” stamped on valve.

 

[Jaredfly]

Thanks guys ! Looks like i will be spending the extra coin on the correct valve. You guys rock ! I will post pics when i get it home.

 

[Mike X485]

:ditto: 10ford saved me the time. The valve is easy to change, remove the existing one and install the new one. Not sure what JD is referring to, but there are no lines or hoses attached to the valve. By the way I think the price of the new valve is around $240.00 now. :crybaby: :trink39:

 

[Jaredfly]

240.00 ?? Oh My !! Makes the good deal im getting not look so good after that hit.

 

[Jaredfly]

Is the part number BW15043 and AM121248 the same valve that's need for the loader ? Price is way different but do they both do the same function ?

 

[Mike X485]

Is the part number BW15043 and AM121248 the same valve that's need for the loader ? Price is way different but do they both do the same function ?

I think that BW15043 was replaced by AM121248.
BW15043 is no longer available on the JD Parts site.

 

[Wooly]

Jaredfly, also take into consideration that with the new valve you also need to install a new free wheel valve lever. The original lever doesn't work with the new valve.

 

[Wooly]

I think that Urban Tractor has a great thread about this very subject. I'm posting from my phone so I can't do a search for it right now.

 

[aquist06]

When I installed the loader on my X728 it wasn't bad at all. The relief valve is taller than the existing one, so you need to replace the bar that you lift to move the tractor when the engine is off. The shutoff valve just replaces the elbow in the line going to the bottom fitting I think, either way, its the only one that has a fitting, all the rest have elbows bent into the metal lines going into the quick connects. The hardest part for me was getting the tube in, I had to put a block of wood on the end and use a hammer to get it in, my brother was underneath making sure I didn't catch anything when it was going through.

Good luck,

Adam

 

[Jaredfly]

Thanks guys, Looks like i am on the right path to getting everything i need to do this install. Special thanks to MikeX485 for the countless PMs with part numbers and advice.

When i get everything on hand i will post some pictures for sure.

 

[slkpk]

Were looking forward to some pics of it when you get it going. slkpk

 

[8086bruce]

Congrats, can't wait to see it!

 

[UrbanTractor]

I think that Urban Tractor has a great thread about this very subject. I'm posting from my phone so I can't do a search for it right now.

Here's a link to that thread: Optional Components Required for FEL on X700 Series

Jaredfly, the valve you are talking about is the Transaxle Hydrostatic Relief Valve (THRV), not to be confused with the Implement Relief Valve (IRV).

These guys are correct, you need the 2WD valve. We haven't updated that link above to explain this distinction -- I will try to get that fixed soon.

 

[Jaredfly]

Just got off the phone setting up a time tomorrow to pick up the 45 loader. I was told that all parts are included and acounted for. Also included is a new lock-out valve which is on the list of needed parts so that's a plus. Then it comes with the trans relief valve but it's for the x5 so I wouldn't be needing it.

I have part numbers to order the following

M146148 free wheeling lever
BW15043 trans relief valve for x4 series
M806205 shims
M805974 shims

Anything else you pros think I will need ?

 

[UrbanTractor]

Lots of ballast.

Also, I'd want the bucket regen, but that's me.

 

[Jaredfly]

Lots of ballast.

Also, I'd want the bucket regen, but that's me.

I asked about that. Says no longer available ?? Any idea where or who has them ?

 

[UrbanTractor]

Huh? News to me. I wonder if the part number could have been superseded?

Hopefully someone else will come along with some info.

 

[Sergeant]

I asked about that. Says no longer available ?? Any idea where or who has them ?

Call those Numbers I Gave You Talk to Gary and ask about the Bucket Regen Kit The Old Number of BM20714 was superseded By this New Number BM22220 Tell Him which store Your Picking it Up at He can Call the store and They'll order the right Kit:thThumbsU