My Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. For Sale & Wanted to Buy (Your Location)
    Hey Garden Tractor Folks. I've been restoring these things for years and My health has finally got me down. I've got several complete tractors just itching to be restored. all have something wrong with them, just the usual stuff. I've got 3 GT18s with ONAN engines, Carb work on 2, powder coat...
  2. John Deere FAQ and Stickies Section
    Hello all, I'm looking for help in repairing an Onan P218 in a JD 318. The engine threw a rod, and the remains of it ended up in the oil pan. I'm in the process of stripping the engine down to the block, and am currently stymied in removing the timing gear (any hints other than building a...
  3. Craftsman/Sears Forum
    I rebuilt the carburetor not long ago and the tractor was running fine, but after sitting for a few weeks it's having some carburetor issues. I pulled the top of the carburetor off and there was only a little fuel in the bottom of the bowl. I bumped the starter and fuel shot out of the hole that...
  4. Generators
    So when I built my house I installed a Kohler RDT-CFNC-200ASE transfer switch and had planned on a Kohler natural gas unit until recently losing gas service during a freeze. I ended up purchasing a Diesel Cummins-Onan 50DGCA rated at 33kw single phase. I am trying to figure out how to wire the...
  5. Generators
    So when I built my house I installed a Kohler RDT-CFNC-200ASE transfer switch and had planned on a Kohler natural gas unit until recently losing gas service during a freeze. I ended up purchasing a Diesel Cummins-Onan 50DGCA rated at 33kw single phase. I am trying to figure out how to wire the...
  6. John Deere Forum
    I ordered some new piston rings for my Onan p218g that I’m rebuilding. They are not OEM. They were supposed to be the right rings. I even spoke with Boomer and he verified that the model number matched. However, after looking at them they look completely different from the original oil rings...
  7. Small Engines and Repair Stickies
    Hi all I have a 18hp B43g engine and i recently replaced the fuel filter and spark plugs as it sounded rough. I have just picked up this skid steer. Now it is hard to start and once it starts it runs for a very short while and then starts to die out. I swapped the old plugs back in and same...
  8. Case_Ingersoll_Colt Forum
    I recently acquired my first garden tractor, a first generation Case 446 with the onan 43 engine, I have got it running but it unfortunately only one cylinder seems to be running correctly, the other one has really low compression and seems to make some weird clacking noises when starting. I...
  9. Gravely
    So my ignition switch went bad while the engine was running and apparently caused the starter to engage and damage the ring gear, starter gear and the engine block where the starter bolts to it. I was directed to another post for Onan P216/P218/P220 for the same issue and a repair by replacing...
  10. John Deere Forum
    Hi there I am new to this site. I've had my 316 for roughly 6 years now and this year I decided to address the famous flyball spacer issue I've been having. I've spoken to boomer and he's shipped me the parts I need to do the job. However, I am now looking for a snowblower attachment for sale...
  11. Gravely
    The original DD13 carb on this engine (on an 8163T i think) is broken - interior pieces of the casting are broken - and I'm having a heck of a time finding the right substitute. I've looked at the Nikki for the B48 and P series but they have a much bigger mounting base which doesn't fit my...
  12. Small Engines and Repair
    Where do i even start?.... We did a quick service in the spring - Oil, Filter, Spark Plug and Air filter along with fresh Premium gas Started rough Exhaust out of only 1 muffler After running fo about 10 minutes - lots of white smoke....
1-12 of 12 Results
Top