My Tractor Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 134 Results
  1. Small Engines and Repair
    Hi All, I picked up a 'free' John Deere 115 (I think it's a 2006) in non-running condition. I was hoping it was the normal gummed up carb or maybe a bad fuel pump, but in this case the connector rod was broken. The flywheel and crankshaft was spinning, but zero compression and when I looked in...
  2. BIG John Deeres
    Hello everybody and thanks in advance if anyone can help , our tractor (2003 Jd 6320) is having a failure while idle it seems to run on 3 cylinder but if we increase the engine speed above 1100rpm it stops failing and runs well , injectors and pump cleaned , no oil leaking and while running on...
  3. John Deere Forum
    There is a 318 for sale within driving distance advertised for $750. I have just seen a few photos so far but it looks like it is in good condition and has a deck. I see this model is very popular on the forum and have been wondering why? I have found that some vehicles (cars/vans) seem to me to...
  4. IH Farmall
    have a jd 5325 tractor. I replaced clutch in it. The hydraulics stopped working. Hydraulic lines full of air. I found some debris in the steering sector and removed it. This fixed that problem. The 3 point hitch will not work now. Any suggestions to what's wrong? The tractor ran fine before
  5. For Sale & Wanted to Buy (Your Location)
    Original Lockout Valve removed from my 2002 X595. In excellent working condition, I have simply replaced it with a quarter-turn valve to save my arthritic fingers. Shipping to the lower 48 states is included.
    $135 USD
  6. For Sale & Wanted to Buy (Your Location)
    Plow Blade, Quick Hitch and John Deere "Bucket" used but in great working order. This came with my recently purchased X595. You will need to confirm if this model will fit your machine or not. I don't know. Standard 54 inch plow blade with easy on/easy off Quick Hitch. Includes the John Deere...
    $1,300 USD
  7. For Sale & Wanted to Buy (Your Location)
    Looking for the mounting/hitch plate (tractor-side) attachment for a John Deere MC519 leaf cart. Any ideas on reproductions are welcome. John Deere Part# M115521
  8. John Deere Forum
    I have a 1976 John Deere 300 in a garage cabin. Been about 10 years since anyone ran it. I want to get it to the dealer for full service work as it will be my snow plow back our road going forward. How do I disengage the tractor so the wheels spin freely and I can put it on my truck?
  9. Backyard Round Table: L & G Tractor Related Topics
    I'm interested to find out if anyone has done any clever mods to make it easy to fill a K46/T40 transaxle without having to take it off the lawn tractor. I've searched around and found one mod where someone drilled a hole below the vent cap. I found another where it looked like someone JB welded...
  10. John Deere Forum
    I acquired a Cozy Cab for my 430 that I recently "restored" with some modern upgrades. I added 20% tint, front and rear light bars as well as rewired the interior of the cab functions. The main reason I had gotten the cab was for the winter but I decided to look into options for if I wanted to...
  11. John Deere Forum
    I bought a new hood for my lx178 and i can’t figure out how to get the bumper and hinge part off. Does anyone know how to? Thanks
  12. BIG John Deeres
    Hello. I have a 1997 6068 225 that’s surging when reved up. Will lope from 1200rpm to 1500rpm when throttle is applied, won’t rev any higher. Fuel supply system is good. I’m thinking governor, where is the governor located on these engines? I’ve heard of a plastic gear wearing down on other...
  13. John Deere Forum
    I have a John Deere G100 with a Tecumseh Enduro 17 I swapped on it. I have put a much stiffer spring on the governor, now the lowest it will idle is at what was previously full throttle, and the motor will rev as high as it can manage to with everything else mostly stock other than fuel system...
  14. John Deere Forum
    So my mower is running great engine wise. Good belts. No issue with belt engagement. But, I can go Rev very slowly, and going FWD will start to go too quick on pressing the pedal. Then it'll jolt a bit when I let up and won't re-engage going FWD until I press reverse. Maybe the external linkage...
  15. Lawn and Garden Tractor Accessories
    Hi, does any know a good Striper kit for an x495 with a 54 inch deck. I’ve looked online and they all don’t say they have compatibility with my mower. I have a budget of about 200 usd.
  16. John Deere Forum
    I just put my JD 400 transaxle back together after service, I just took off the right side plate put Hylomar and all new o-rings/bushings, now it goes in reverse when I am not pushing the forward or reverse pedal and seems to be slower than it was. Any ideas what I messed up? Thanks!
  17. John Deere Forum
    Hello, I’ve noticed recently that when I turn the deck blades on my 322 (50” deck), the middle blade spins first, and the outer blades don’t. Eventually the outer blades will start to spin. I used ramps so I could see what was happening at different points in the mow. Once the outer blades...
  18. Backyard Round Table: L & G Tractor Related Topics
    Cub Cadet LT1046 With a Kawasaki FS541V engine. Issue: Backfired one day, while mowing and a big white puff of smoke came out and died. It did start up again and now surges badly, like a bad carburetor would. Heres what I have done: New carburetor, two new spark plugs and coil packs, Adjusted...
1-19 of 134 Results
Top