My Tractor Forum banner

Search results

1-20 of 469 Results
Advanced Search
  1. Ethanol free gas question

    John Deere Forum
    I put seafoam in all my small engine fuel as soon as I pump it. (nonethanol) I never drain a tank or run them dry. Never an issue. Thats for boats, tractors weedeaters chainsaws- you name it
  2. Amt 622

    ATV's, RTV's, UTV's, and Snow Mobiles
    I need something with a hydraulic dump and an AMT622 has come up for sale near me. What should I be on the lookout for with this machine ? Or just avoid it ? I know little about them except that it would appear to suit my needs. Thanks for any guidance
  3. Amt 622

    John Deere Forum
    I know this is not a topic specified for this page,but the type of people and amount of traffic here led me to try it anyway. Ive also posted on the UTV section but there is not much traffic there. Im looking for something with a hydraulic dump. One of these AMT622's is available near me but I...
  4. Plow Blade Interchangability

    John Deere Forum
    Getting it, If it doesnt adapt easily- my bro in law just bought a x3xx something tractor last week and it will mke a nice christmas gift
  5. Plow Blade Interchangability

    John Deere Forum
    Re: Blade nterchangability Im talking about a 42" plow blade. I edited my post to say plow blade. I understand the confusion after rereading my original post.
  6. Plow Blade Interchangability

    John Deere Forum
    Any chance a Plow blade for an x300 will fit an old LX188 ? I doubt it but couls it be modified easily ? Found an x300 blade and 2 suitcase weights nearby for $150. Almost cant pass it up
  7. Just got my first JDs, questions

    John Deere Forum
    The advantage of the rear mower is that it can be used with the loader in place. The loader (most likely) runs on its own pump using the front power take off, which the mid mount mower would also need to operate.
  8. Poor man's deck paint job options

    John Deere Forum
    I chipped away as much powder coat and used a random orbit sander to get most of the rust off as many spots as I could , then just rattle canned a couple coats of jd yellow from the hardware store on one. Two years later its still looking ok. Like you , I was just looking to stop the rust and...
  9. Gator Blades-Any Good-Which ones

    John Deere Forum
    Ive seen several people on this and other sites have put G5's on their piranha decks. I see they are sold in 6 packs, so do you put 2 of those monsters on each spindle ? Or are they just selling 2 sets of blades ? Do you just put one G5 on each spindle, or do you put the second OEM blade on with...
  10. 44 Piranha and G5 Gator blades

    John Deere Forum
    Ive seen several people on this and other sites have put G5's on their piranha decks. I see they are sold in 6 packs, so do you put 2 of those monsters on each spindle ? Or are they just selling 2 sets of blades ? Do you just put one G5 on each spindle, or do you put the second OEM blade on...
  11. World's worst cut?

    John Deere Forum
    Id bet that bouncing spring you mentioned is the key to your problem. Im betting the deck belt is the wrong one, or installed wrong or just not tight.
  12. Goid deal?

    John Deere Forum
    I didnt know an MTD 3 pt hitch would fit a JD 400
  13. 48" Replacement Deck - Rebuild Problems

    John Deere Forum
    Its a 50- 50 looks nothing like a 48. Google images of both and you will see.
  14. LX279 or LX280

    John Deere Forum
    Ilove my watercooled Kawasaki- although its on an older LX188- I am meticulous about checking it and maintaining it. With 6 different people operating your machine- I would opt for the air cooled and hope 4 of the 6 at least check the oil.
  15. Not entirely happy with snowblower on x758

    John Deere Forum
    It looks like a lot of snow comes out the top center of the housing instead of being eaten by the impeller. Single stages have a plate to prevent that to some degree. Seems the impeller isnt sufficient to swallow what the augers bring or the augers arent good at stuffing it into the impeller...
  16. Steel camshaft sources

    John Deere Forum
    Im thinking I should replace the cam in my Kawi FD501v. My son is going to be taking a small engine class at school and this would be a good project to work on. What else do I need besides the camshaft and new gaskets ? Where do I find the parts ? Is this a Deere only thing or can I get...
  17. 214 vs. 318: Which to blow snow and which to push it?

    John Deere Forum
    Now I think you just need a rockshaft lockout - to keep that cylinder from cycling when you use the angle hydraulics,
  18. 214 vs. 318: Which to blow snow and which to push it?

    John Deere Forum
    5 minutes to not blow snow with a gear drive is more than worth the effort:tango_face_devil:
  19. 214 vs. 318: Which to blow snow and which to push it?

    John Deere Forum
    So now, you can see it takes about 5 minutes to switch the 318 from one to the other so you can park the 214 and just switch back and forth on the 318 and utilize the hydrostatic drive and hydraulics with both implements
  20. 214 vs. 318: Which to blow snow and which to push it?

    John Deere Forum
    Awesome score, you'll want to rig up a way to angle from the seat or fab a hydraulic angle setup ASAP.
1-20 of 469 Results
Top