MyTractorForum.com - The Friendliest Tractor Forum and Best Place for Tractor Information - View Profile: Richard-tx

Richard-tx Richard-tx is offline

5000 Strong & Climbing

  Visitor Messages

Showing Visitor Messages 1 to 5 of 5
  1. ckaine
    05-11-2016 10:39 AM - permalink
    ckaine
    Hello Richard:

    As one of the most experienced folks on the Gravely Site, I was wondering if you could direct me to a vendor that has replacement seats for my 8179 Gravely. I would like something not needing much 'finagling' to get attached, and that would also be similar in Seat Back Height.

    Regards;

    Chris
  2. PaPa Mark
    02-27-2016 11:15 AM - permalink
    PaPa Mark
    Not sure if I am doing this right or not, I am hoping this is a direct e-email to Richard-tx. On one of my threads you offered to help out with my gravely on a trip you planned to Evergreen. I was off line a couple of weeks so do not know if your trip is completed or not. If you get this e-mail please contact me, thanks - Mark 3034034233
  3. norwee
    09-16-2015 01:50 PM - permalink
    norwee
    richard,
    I lurk on mtf, gt talk, and other tractor forums. I picked up a 16 g and I have an opportunity to add a 816. I have a L model that has no compression. My question,finally, would it be better to run a brush hog deck from a two wheel gravely off of an 816? just looking for some advice
  4. Kaotic01
    09-08-2014 11:43 AM - permalink
    Kaotic01
    Any word on when I should get the drive shaft boxed up and ready to go out via USPS ?
  5. hiegear
    07-08-2014 06:36 AM - permalink
    hiegear
    I am looking to buy a new set of rims for my Pro 12. I remember you pointed out the best source but can't find the thread. Would you please direct me to the source? Thanks, Billy Gear

  About Me

  • About Richard-tx
    Location
    TX - DFW
  • Signature
    Code:
                                  Current Inventory
       24G (Onan 24hp)    24GLX - was 16G  (Onan 24hp)   8249 - was 8129 (Onan 24hp)
            818T (Onan 18hp B48)       8163T - was 8123 (Onan CCKA) 
                                  8183T (Onan B48)
       5665 w/brakes        5665        5660        Pro-8         Pro-16 w/brakes
    
    For Gravely Manuals and more visit http://GTCOA.com

  Statistics

Total Posts
Visitor Messages
Gallery
General Information
  • Last Activity: 10-29-2018 11:47 AM
  • Join Date: 10-05-2010
  • Referrals: 0

  Mentions

No results to display...

  Quotes

06-16-2019
08:22 AM - Gravely1961 quoted Richard-tx in post Re: Commercial 12 PTO issue
Hi all ó Iím having the same is...
10-29-2018
08:39 PM - Steve Urquell quoted Richard-tx in post New (unwelcome) experience while using a Gravely
For underground yellow jacket n...
11:38 AM - Richard-tx quoted rydforlyf in post Re: Bearing Removal on 30" 106 Brush Mower
Nicely done. I'm a card ca...
11:36 AM - Richard-tx quoted glrutkosx in post Re: Gravely L Model Conversion to Solid State Ignition ?
Does anyone know if it is feas...
07-15-2018
11:40 AM - cfichuck quoted Richard-tx in post Re: Best Gravely for rough bumpy mowing
The smoothness of the IH140 is ...
07-08-2018
10:01 AM - Richard-tx quoted County5665 in post Re: 5665- K301- Low power- Rough running
And a concluding post: After...
06-15-2018
04:01 PM - Richard-tx quoted Greg in WV in post Re: Rotary plow questions
It may be possible to get a lit...
06-09-2018
10:19 PM - flash5153 quoted Richard-tx in post Re: 8123 engine parts? 12hp Kohler K301-s
I guarantee that if you mic the...
06-03-2018
09:18 AM - cmeyers77 quoted Richard-tx in post Re: Machining LI or LS Ring Gear to Fit Swiftamatic
You would not need to go so slo...
05-23-2018
09:56 AM - Gravely Frank McM quoted Richard-tx in post Re: 30 in deck just pushes grass over
The blade in this picture is wo...
05-22-2018
08:17 PM - Areid5651 quoted Richard-tx in post Gravely 812 loss of power
...ing Tapatalk [QUOTE=Richard-tx;11939065]How does th...
12:39 PM - Gravely Frank McM quoted Richard-tx in post Re: 30 in deck just pushes grass over
:wwp::wwp::wwp: A picture of...
05-21-2018
09:44 PM - Gerrard quoted Richard-tx in post Re: 30 in deck just pushes grass over
Gravely has made RH and LH blad...
05-20-2018
11:22 AM - ATLANTIC CENTRAL quoted Richard-tx in post Re: Sheave and Spindle Splines Stripped
The locking nuts are the nylock...
05-19-2018
07:50 PM - Gerrard quoted Richard-tx in post Re: Now Whats Wrong?
The clearance between the hub a...
05-11-2018
04:38 PM - ChrisPBuBBa quoted Richard-tx in post Re: Gravely 566
If the tractor has been used fr...
05-09-2018
12:29 PM - jj94tt quoted Richard-tx in post Re: New foot treads for 800 series and other stuff
No one addressed the exhaust is...
04-20-2018
10:57 AM - sharkman quoted Richard-tx in post Re: tired of pulling the the hand start units???
Check the Gravely Dealer notes ...
04-09-2018
12:37 AM - Fla Don quoted Richard-tx in post Re: Look at this overkill
Properly done, a properly crimp...
04-01-2018
09:04 PM - Richard-tx quoted Gerrard in post Re: Is this notch-or cut OK in this piston ?
@ Richard-tx, Here's what it...
 
For the best viewing experience please update your browser to Google Chrome