MyTractorForum.com - The Friendliest Tractor Forum and Best Place for Tractor Information - View Profile: onanparts.com

onanparts.com onanparts.com is offline

Senior MTF Member

  Visitor Messages

Showing Visitor Messages 1 to 6 of 6
  1. inspectorudy
    03-24-2018 08:23 PM - permalink
    inspectorudy
    Finally got the 24 running and the right cylinder is leaking oil into the cylinder and it fouled the plug to the point that I couldn't tune it. The right side is fine with a nice tan plug. The front crank seal is leaking also so I will need to replace that too. Is this the correct seal for the PTO end? 509-0041 Rear Main Seal CCK, MCCK B, P & N Series. Can you give me a quote on a set of rings, head gasket, and this seal? Thanks. I was looking at Onan's site and they want $35 for the ring set, $13 for the seal and $13 for the head gasket.
  2. jimbo316
    07-28-2017 07:46 AM - permalink
    jimbo316
    first much thx for your advice over the years

    any thought on my breather tube Q below

    https://www.mytractorforum.com/12-joh...l#post11027706

    thx

    jim
  3. twofitu
    06-09-2016 07:34 AM - permalink
    twofitu
    [email protected] - thanks for the manual, all I've got is the Sears manual and it has only very basic maintenance.
  4. mydeere318
    11-02-2015 07:28 PM - permalink
    mydeere318
    Hi, I have a John Deere 318 with a P218g that has a broken starter mount on the block, I posted my issue on the Jd forum page for help and what I have done so far is purchase an oil pan and dipstick from a B43 and a B43 inertia style starter that bolts to the oil pan.have oil pan on, starter aligned, but starter will not turn engine over with the spark plugs in. I had the starter (onan) checked out at repair shop and a bushing was replaced, took back and repair shop said bushing was still tight going to pick up tomorrow.should this starter work ok with my engine, even if I have to buy a new one. thank you for your help
  5. toppop52
    02-04-2013 09:22 PM - permalink
    toppop52
    Hi, i was wondering if by using the factory adapter there is any reason I couldn't use a Nikki carb on my B48M. They are sure a lot easier find and way cheaper.
    Thanks,
    Randy
  6. biker3777
    12-19-2010 08:38 AM - permalink
    biker3777
    I am in the process of changing the engine in my 318,it had a B43 and I found a motor out of a Sears tractor so I rebuilt it and put it in the frame and the starter would not turn the engine over so I took it out and it mounts different than the B43,after a lot of research I thought it might be Linamar but after more research I think it is a G model 218 with a 191-1828 starter.What was the "g" model difference?

  About Me

  Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 04-17-2019 08:55 PM
  • Join Date: 11-13-2008
  • Referrals: 0

  Friends

Showing Friends 1 to 2 of 2
  • winger4554
    • winger4554 is offline
  • WvBURBAN
    • WvBURBAN is offline

  Mentions

No results to display...

  Quotes

11-01-2018
06:32 PM - onanparts.com quoted tractorguy5000 in post Re: onan b43m
does anyone have a rebuildable b43m...
08-30-2018
06:22 PM - Mowtoit quoted onanparts.com in post Re: B43G Engine serial number?
You're welcome! Based on your dete...
06:17 PM - onanparts.com quoted Mowtoit in post Re: B43G Engine serial number?
I looked at the numbers you ...
11:19 AM - onanparts.com quoted Mowtoit in post Re: B43G Engine serial number?
So the 'stamped in the block...
05-15-2018
12:05 AM - onanparts.com quoted jstiz in post Re: Massey 1655 w/18hp Onan , bad ignition coil?
Looks to be the module, do...
04-23-2018
10:10 AM - onanparts.com quoted 1969140 in post Re: Onan front seal replacement
The possible oil pressure sw...
04-13-2018
10:43 PM - Todd_D quoted onanparts.com in post Re: Bagged a nice 420 today
This is a neat vid, clear plastic ...
04-10-2018
02:23 PM - onanparts.com quoted inspectorudy in post Re: Bagged a nice 420 today
I'm with you Todd on what to do e...
04-06-2018
09:43 PM - dirtsaver quoted onanparts.com in post Where do yall buy original parts
The easiest parts to find are for ...
04:43 PM - Ssgtparshall quoted onanparts.com in post Re: Where do yall buy original parts
The easiest parts to find are for ...
03-28-2018
03:10 PM - onanparts.com quoted inspectorudy in post Re: Bagged a nice 420 today
When I took the piston out there ...
03-27-2018
09:59 PM - onanparts.com quoted inspectorudy in post Re: Bagged a nice 420 today
My God! If ever I need a cheerlea...
05:02 PM - onanparts.com quoted inspectorudy in post Re: Bagged a nice 420 today
On the top of the piston, it says...
04:22 PM - onanparts.com quoted inspectorudy in post Re: Bagged a nice 420 today
Took a look at the rings in the b...
03-06-2018
08:14 PM - onanparts.com quoted nick4030 in post Re: Case 646
I then reset the valves, ther...
03-04-2018
12:19 PM - ssmewing quoted onanparts.com in post Re: Case 646
Was going to suggest listening wit...
04:30 AM - onanparts.com quoted nick4030 in post Re: Case 646
No it doesn't. I have it read...
02-27-2018
01:03 AM - onanparts.com quoted RussKish in post Re: oil light came on?
What is the thread on the oil...
12:34 AM - onanparts.com quoted inspectorudy in post Re: oil light came on?
...uine Onan ones for, inspectorudy. $14.95 :) 1/8 x ...
02-26-2018
11:17 PM - RussKish quoted onanparts.com in post Re: oil light came on?
P224G it is. :) NC oil switch for ...
 
For the best viewing experience please update your browser to Google Chrome