Model L & C Gear Ratio Identification - MyTractorForum.com - The Friendliest Tractor Forum and Best Place for Tractor Information
Register Home FAQ Garage MTF Gallery Search Today's Posts Mark Forums Read Store Chat Room

 
 
Thread Tools Display Modes
Old 12-26-2011, 09:20 PM   post #1 of 1
feold3
RIP Chip, "Gravely Guru, Gone But Not Forgotten"
 
feold3's Avatar
 
Join Date: Jan 2011
Location: Maryland
Posts: 27
MTF Member # 54255
Default Re: Is it an Li?

Model L & C Gear Ratio Identification

Beginning in 1954 the Model L could be ordered with three different gear ratios, determined by the number of "leads" on the worm. A Model L's gearing is identified by the model shown on the large ID plate on top of the fuel tank. Model L is the fast speed model (8-lead worm), Model LI is the intermediate speed model (6-lead worm, and Model LS is the slow speed model (4-lead worm). Those model IDs were stamped on the plate at the end of the assembly line.

On the assembly line he following method was used to identify the gearing before the ID plate was stamped: Look at the right hand axle housing (right hand from the operator's position). When an LI went down the line it had a bolt and nut in one of the holes in the outer flange on the axle housing. An LS had a large washer under one of the six bolts that secure the axle housing to the transmission. A standard L had no bolt in the outer flange and no large washer.

The Model C (Convertible 7.6) was also available in the same ratios, but the small ID plate on the Advance Casting doesn't show whether it is a C, a CI or a CS. Look at the left hand axle housing. When it went down the assembly line an aluminum tag stamped "C", "CI" or "CS" was put under one of the six bolts that secure the axle housing to the transmission. It's possible that early examples of the Model C used the old Model L method described above, so check that too.

Problem is, after all these years the tractor's ID plate may be gone, and the bolt, washer, or tag may have been removed during repairs. In that case the following test can be used to determine the gearing:

- Jack up the tractor so one tire is off the ground. Make sure the other wheel remains on the ground so it can't rotate, or find another way to prevent it from rotating.
- Remove the spark plug, put the cable back on the plug, and ground the plug on the engine to prevent magneto damage.
- If electric start, remove the starter chain so the crankshaft can be rotated by hand.
- Lock the high/low clutch lever into low.
- Lock the forward/reverse clutch lever into forward.
- If it is a Swiftamatic, engage high range.
- Rotate the crankshaft and count how many crankshaft revolutions it takes to rotate the wheel 1/4 turn.

L or C (8-lead worm)
1/4 wheel rotation requires 6 crankshaft rotations.

LI or CI (6-lead worm)
1/4 wheel rotation requires 9 crankshaft rotations.

LS or CS (4-lead worm)
1/4 wheel rotation requires 12 crankshaft rotations.
__________________
Chip Old
Cub Hill, Maryland, US

Free Gravely Manual Downloads: www.oldgravelys.net/docs/
Gravely Tractor Club of America: www.gravelytractorclub.org/

Last edited by DJ in WV; 12-26-2011 at 09:36 PM.
feold3 is offline   Quick reply to this message
Sponsored Links
Advertisement
 
 

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the MyTractorForum.com - The Friendliest Tractor Forum and Best Place for Tractor Information forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:23 PM.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.
Compact Tractor Reviews Tractor Reviews Snowblowers Lawn Mower Forum
My Tractor Forum Snow Thrower Power Equipment Forum
Combine Forum Snowblower Forum ATV and UTV Reviews